The standing seams are laid flat 8" from the vertical wall, folded 3/4" and secured with copper cleats spaced 12" O.C. Flashings in single wythe walls, like cavity walls should be positioned to direct water to the exterior.
As shown in Figure 1, the flashing in a cavity wall at the intersection of the foundation should be sealed to the exterior faceshell of the backup wythe, project downward to the foundation surface, outward to the exterior face of the wall, and terminate with a sloped drip.
The Shot-Blast Designer Block features a subtle exposed aggregate finish. As shown in Figure 9, the flashing should project through the wall and be carried up on the interior concrete masonry surface. The Masonry Detailing Series (MDS) is an exhaustive collection of illustrative construction details and diagrams produced by International Masonry Institute (IMI) for architects and engineers to use as a design resource. Bar, 01.070.0301: Base of Wall – Adhered Veneer Over CMU, No Drainage Mat, 01.410.0201: End Dam Diagram – Field-Formed Flashing End Dam, 01.410.0202: End Dam Diagram – Prefabricated Flashing End Dam, 01.410.0311: Elevations – Mortar Joint Material Takeoff, 01.410.0401: Face Brick – Allowable Distortion, 01.410.1311: Elevations – Movement Joint Layout, 01.410.1401: Allowable Construction Tolerances, 01.410.1411: Allowable Variations of Masonry – Out-of-Plumb, 01.410.1412: Allowable Variations Of Masonry – Out-of-Line, 01.410.1413: Allowable Variations Of Masonry – Out-of-Line, 02.010.0311: Base of Wall Detail – Single Wythe Block, Split Base Course, 02.010.0312: Base of Wall – Single Wythe Block, Flashing at Inside Face, 02.010.0313: Base of Wall – Single Wythe Block, Proprietary Flashing/Weeps, 02.010.0401: Sill Detail – Single Wythe Block, 02.010.0702: Concrete Masonry Firewall – T/ Wall at Slab Above, 02.010.0801: Masonry Wall Cap – Single Wythe CMU, 02.010.1301: Control Joint – Preformed Gasket, 02.020.0202: Vertical Span – CMU Partition, 02.020.0203: Horizontal Span – CMU Partition, 02.120.0101: Wall Section – Hybrid Wall System, 02.120.0102: Wall Section – Hybrid Wall System, 02.120.0501: Jamb Detail – Storm Shelter Window / Door Jamb, 02.120.0601: Head Detail – Storm Shelter Window / Door Head, 02.120.0701: Floor Detail – Hybrid Type I & IIa, 02.120.0702: Floor Detail – Hybrid Type IIB, 02.120.0711: Floor Connection Detail – Option 1, 02.120.0712: Floor Connection Detail – Option 2, 02.120.0713: Floor Connection Detail – Option 3, 02.120.0751: Plank at Bearing Wall – Intermediate Elevation. However, the bond-breaking effects of this type of detail need to be evaluated in regard to the structural performance of the wall. (Courtesy of the Concrete Masonry Association of California and Nevada).
(102 mm) over the face of the masonry and sealed on both sides. DWG files are available upon request. The cap flashing is attached to the base flashing by blind riveting. The top of the roof pan is formed into a "bread pan" whose upper edge is just above the finished batten. Find your polling place or ballot dropbox here:…, This site uses cookies and collects basic information. A copper receiver holds the counterflashing at its top edge. Next, a section of pliable self-adhering membrane (such as rubberized-asphalt) or other pliable membrane set in mastic is fully bonded to the flashing at the location of the gap. Exterior Walls, Interior Walls
As shown in Figure 1, the flashing in a cavity wall at the intersection of the foundation should be sealed to the exterior faceshell of the backup wythe, project downward to the foundation surface, outward to the exterior face of the wall, and terminate with a sloped drip.
The Shot-Blast Designer Block features a subtle exposed aggregate finish. As shown in Figure 9, the flashing should project through the wall and be carried up on the interior concrete masonry surface. The Masonry Detailing Series (MDS) is an exhaustive collection of illustrative construction details and diagrams produced by International Masonry Institute (IMI) for architects and engineers to use as a design resource. Bar, 01.070.0301: Base of Wall – Adhered Veneer Over CMU, No Drainage Mat, 01.410.0201: End Dam Diagram – Field-Formed Flashing End Dam, 01.410.0202: End Dam Diagram – Prefabricated Flashing End Dam, 01.410.0311: Elevations – Mortar Joint Material Takeoff, 01.410.0401: Face Brick – Allowable Distortion, 01.410.1311: Elevations – Movement Joint Layout, 01.410.1401: Allowable Construction Tolerances, 01.410.1411: Allowable Variations of Masonry – Out-of-Plumb, 01.410.1412: Allowable Variations Of Masonry – Out-of-Line, 01.410.1413: Allowable Variations Of Masonry – Out-of-Line, 02.010.0311: Base of Wall Detail – Single Wythe Block, Split Base Course, 02.010.0312: Base of Wall – Single Wythe Block, Flashing at Inside Face, 02.010.0313: Base of Wall – Single Wythe Block, Proprietary Flashing/Weeps, 02.010.0401: Sill Detail – Single Wythe Block, 02.010.0702: Concrete Masonry Firewall – T/ Wall at Slab Above, 02.010.0801: Masonry Wall Cap – Single Wythe CMU, 02.010.1301: Control Joint – Preformed Gasket, 02.020.0202: Vertical Span – CMU Partition, 02.020.0203: Horizontal Span – CMU Partition, 02.120.0101: Wall Section – Hybrid Wall System, 02.120.0102: Wall Section – Hybrid Wall System, 02.120.0501: Jamb Detail – Storm Shelter Window / Door Jamb, 02.120.0601: Head Detail – Storm Shelter Window / Door Head, 02.120.0701: Floor Detail – Hybrid Type I & IIa, 02.120.0702: Floor Detail – Hybrid Type IIB, 02.120.0711: Floor Connection Detail – Option 1, 02.120.0712: Floor Connection Detail – Option 2, 02.120.0713: Floor Connection Detail – Option 3, 02.120.0751: Plank at Bearing Wall – Intermediate Elevation. However, the bond-breaking effects of this type of detail need to be evaluated in regard to the structural performance of the wall. (Courtesy of the Concrete Masonry Association of California and Nevada).
(102 mm) over the face of the masonry and sealed on both sides. DWG files are available upon request. The cap flashing is attached to the base flashing by blind riveting. The top of the roof pan is formed into a "bread pan" whose upper edge is just above the finished batten. Find your polling place or ballot dropbox here:…, This site uses cookies and collects basic information. A copper receiver holds the counterflashing at its top edge. Next, a section of pliable self-adhering membrane (such as rubberized-asphalt) or other pliable membrane set in mastic is fully bonded to the flashing at the location of the gap. Exterior Walls, Interior Walls
As shown in Figure 1, the flashing in a cavity wall at the intersection of the foundation should be sealed to the exterior faceshell of the backup wythe, project downward to the foundation surface, outward to the exterior face of the wall, and terminate with a sloped drip.
The Shot-Blast Designer Block features a subtle exposed aggregate finish. As shown in Figure 9, the flashing should project through the wall and be carried up on the interior concrete masonry surface. The Masonry Detailing Series (MDS) is an exhaustive collection of illustrative construction details and diagrams produced by International Masonry Institute (IMI) for architects and engineers to use as a design resource. Bar, 01.070.0301: Base of Wall – Adhered Veneer Over CMU, No Drainage Mat, 01.410.0201: End Dam Diagram – Field-Formed Flashing End Dam, 01.410.0202: End Dam Diagram – Prefabricated Flashing End Dam, 01.410.0311: Elevations – Mortar Joint Material Takeoff, 01.410.0401: Face Brick – Allowable Distortion, 01.410.1311: Elevations – Movement Joint Layout, 01.410.1401: Allowable Construction Tolerances, 01.410.1411: Allowable Variations of Masonry – Out-of-Plumb, 01.410.1412: Allowable Variations Of Masonry – Out-of-Line, 01.410.1413: Allowable Variations Of Masonry – Out-of-Line, 02.010.0311: Base of Wall Detail – Single Wythe Block, Split Base Course, 02.010.0312: Base of Wall – Single Wythe Block, Flashing at Inside Face, 02.010.0313: Base of Wall – Single Wythe Block, Proprietary Flashing/Weeps, 02.010.0401: Sill Detail – Single Wythe Block, 02.010.0702: Concrete Masonry Firewall – T/ Wall at Slab Above, 02.010.0801: Masonry Wall Cap – Single Wythe CMU, 02.010.1301: Control Joint – Preformed Gasket, 02.020.0202: Vertical Span – CMU Partition, 02.020.0203: Horizontal Span – CMU Partition, 02.120.0101: Wall Section – Hybrid Wall System, 02.120.0102: Wall Section – Hybrid Wall System, 02.120.0501: Jamb Detail – Storm Shelter Window / Door Jamb, 02.120.0601: Head Detail – Storm Shelter Window / Door Head, 02.120.0701: Floor Detail – Hybrid Type I & IIa, 02.120.0702: Floor Detail – Hybrid Type IIB, 02.120.0711: Floor Connection Detail – Option 1, 02.120.0712: Floor Connection Detail – Option 2, 02.120.0713: Floor Connection Detail – Option 3, 02.120.0751: Plank at Bearing Wall – Intermediate Elevation. However, the bond-breaking effects of this type of detail need to be evaluated in regard to the structural performance of the wall. (Courtesy of the Concrete Masonry Association of California and Nevada).
(102 mm) over the face of the masonry and sealed on both sides. DWG files are available upon request. The cap flashing is attached to the base flashing by blind riveting. The top of the roof pan is formed into a "bread pan" whose upper edge is just above the finished batten. Find your polling place or ballot dropbox here:…, This site uses cookies and collects basic information. A copper receiver holds the counterflashing at its top edge. Next, a section of pliable self-adhering membrane (such as rubberized-asphalt) or other pliable membrane set in mastic is fully bonded to the flashing at the location of the gap. Exterior Walls, Interior Walls
Boral manufactures and supplies concrete masonry products in Australia and is recognized as a leading supplier in the paving, landscaping and retaining wall markets with industry-leading range of concrete block and retaining wall products. Face Brick, Term Bar, 01.030.0705: Shelf Angle Detail – Anchored Brick Veneer, CMU Backing, Shelf Angle with Bracket-Type Standoffs, 01.030.0721: Roof Detail – Pitched Roof to High Wall, 01.030.0751: Roof Detail – High Wall – Low Roof, 01.030.0804: Brick veneer, CMU backup, rigid insul. Flashing, Drip Edge, Term. If precautions are not taken, it is suggested that a wider airspace be utilized, i.e. As the temperature fluctuates, the flashing material will expand and contract differently than the masonry material, which can result in sealant failure and a potential point of entry for moisture. 1) which addresses the effect of moisture on masonry, design considerations, flashing materials, construction practices, and maintenance of flashing. The reglet is then filled with sealant. The details provided below are available for your reference and consideration. Metal caps require wood plates for anchorage, which in turn are usually attached to the wall with anchor bolts. The lower edge is hemmed and laps the base flashing and is formed to be a snug fit against the base flashing. (102 mm). Reinforcement Placement, Roof Details
The type of flashing detail to use on low-sloped roofs will in part depend on the type of roofing membrane being used. The composition flashing is extended up a cant strip then up the wall at least 10".
The standing seams are laid flat 8" from the vertical wall, folded 3/4" and secured with copper cleats spaced 12" O.C. Flashings in single wythe walls, like cavity walls should be positioned to direct water to the exterior.
As shown in Figure 1, the flashing in a cavity wall at the intersection of the foundation should be sealed to the exterior faceshell of the backup wythe, project downward to the foundation surface, outward to the exterior face of the wall, and terminate with a sloped drip.
The Shot-Blast Designer Block features a subtle exposed aggregate finish. As shown in Figure 9, the flashing should project through the wall and be carried up on the interior concrete masonry surface. The Masonry Detailing Series (MDS) is an exhaustive collection of illustrative construction details and diagrams produced by International Masonry Institute (IMI) for architects and engineers to use as a design resource. Bar, 01.070.0301: Base of Wall – Adhered Veneer Over CMU, No Drainage Mat, 01.410.0201: End Dam Diagram – Field-Formed Flashing End Dam, 01.410.0202: End Dam Diagram – Prefabricated Flashing End Dam, 01.410.0311: Elevations – Mortar Joint Material Takeoff, 01.410.0401: Face Brick – Allowable Distortion, 01.410.1311: Elevations – Movement Joint Layout, 01.410.1401: Allowable Construction Tolerances, 01.410.1411: Allowable Variations of Masonry – Out-of-Plumb, 01.410.1412: Allowable Variations Of Masonry – Out-of-Line, 01.410.1413: Allowable Variations Of Masonry – Out-of-Line, 02.010.0311: Base of Wall Detail – Single Wythe Block, Split Base Course, 02.010.0312: Base of Wall – Single Wythe Block, Flashing at Inside Face, 02.010.0313: Base of Wall – Single Wythe Block, Proprietary Flashing/Weeps, 02.010.0401: Sill Detail – Single Wythe Block, 02.010.0702: Concrete Masonry Firewall – T/ Wall at Slab Above, 02.010.0801: Masonry Wall Cap – Single Wythe CMU, 02.010.1301: Control Joint – Preformed Gasket, 02.020.0202: Vertical Span – CMU Partition, 02.020.0203: Horizontal Span – CMU Partition, 02.120.0101: Wall Section – Hybrid Wall System, 02.120.0102: Wall Section – Hybrid Wall System, 02.120.0501: Jamb Detail – Storm Shelter Window / Door Jamb, 02.120.0601: Head Detail – Storm Shelter Window / Door Head, 02.120.0701: Floor Detail – Hybrid Type I & IIa, 02.120.0702: Floor Detail – Hybrid Type IIB, 02.120.0711: Floor Connection Detail – Option 1, 02.120.0712: Floor Connection Detail – Option 2, 02.120.0713: Floor Connection Detail – Option 3, 02.120.0751: Plank at Bearing Wall – Intermediate Elevation. However, the bond-breaking effects of this type of detail need to be evaluated in regard to the structural performance of the wall. (Courtesy of the Concrete Masonry Association of California and Nevada).
(102 mm) over the face of the masonry and sealed on both sides. DWG files are available upon request. The cap flashing is attached to the base flashing by blind riveting. The top of the roof pan is formed into a "bread pan" whose upper edge is just above the finished batten. Find your polling place or ballot dropbox here:…, This site uses cookies and collects basic information. A copper receiver holds the counterflashing at its top edge. Next, a section of pliable self-adhering membrane (such as rubberized-asphalt) or other pliable membrane set in mastic is fully bonded to the flashing at the location of the gap. Exterior Walls, Interior Walls
Flashing in CMU, Drip Edge, MDCD, 01.030.0311: Base of Wall Detail – Metal Flashing W/ Drip, Term. Care should be exercised to insure that surfaces supporting the flashing are flat or are sloping to the exterior.
